At first glance, it seems that original handmade rings can only be made by professional craftsmen, and that an ordinary amateur cannot do this. It’s hard to believe that you can make a ring with your own hands that won’t look ridiculous, but will attract the attention of others and delight them.

But it turns out that this can be done at home, and even with some advantages over buying jewelry in a regular jewelry store.

What rings are available for making yourself?

The good thing about original handmade rings is that they have a wide range of materials available: from paper to metals. This emphasizes the unusual nature of such jewelry and is suitable for people of different skill levels. However, different materials require different amounts of time and have different costs.

So what can you make a decorative ring from?

• from paper;
• from fabric;
• from a coin.

Paper ribbon ring

It would seem, how can you make a paper ring that is not a joke and lasts longer than a few minutes? It turns out that this is possible.

You need to take a page of an unnecessary glossy magazine and cut it into strips of equal width. The edge of the resulting paper tape must be secured to the base of the ring.

Next, coat the tape with paper or any other strong glue and cover the base with it. Continue until you have a ring of sufficient width. For the top layer, you can choose paper with some special inscription or a beautiful ornament, because it will represent the type of decoration.

If you dip the resulting product in PVA and then dry it thoroughly, it will be stronger and last longer.

Fabric ring

This type of ring has an advantage over all others: you can make jewelry for each dress or any other clothing, and everything together will look harmonious - you just need to choose the right fabric.

You will need:

• pieces of organza;
• needle and thread;
• beads;
• blank for rings.

How to do:

Cut out several circles of different diameters and singe the edges so that the fabric does not unravel and the circles become convex. Then you need to put these pieces one inside the other and sew them exactly in the middle. The result was “rose” petals.

So that the place where they are fastened is not visible, you need to sew a bead or several beads onto it - this will be the middle of the flower. Then it must be attached with superglue to the base, which can be left as is, or can be covered with fabric or painted in any color.

However, such a flower is suitable not only for a ring, but also for any decoration - you can even create entire sets.

Flower made from a coin

This method is more complicated than the previous ones and involves the use of a drill. The coin must be drilled exactly in the center and placed on the crossbar, on which it should be evenly flattened with a hammer. Having achieved the desired size, sand the resulting ring with sandpaper and it will be ready.

Variety of options

These are simple ideas and instructions on how to make a ring at home. In fact, there are many more methods of varying degrees of complexity and using different materials. They can be seen both in discussions of hand-made craftsmen and in tutorials.

Photos of rings made by yourself amaze with the variety and results of the work. Very often you can find jewelry made from materials that, at first glance, are unsuitable for use in this capacity. But the desire to surprise and do something unusual leads to experiments, and then to non-standard solutions.

Note!

All master classes on handmade rings are divided according to the type of source materials, so you can refer to them to search for original ideas.

Any lesson, live or online, will show all the stages of work clearly, and will also make it clear that there is nothing difficult in creating jewelry yourself.

Even someone who has never done anything like this can start and get good results. Perhaps the first work will turn out with flaws, but with experience will come the ability to do the work quickly and efficiently, which leads to real mastery that delights others.

DIY ring photo

Note!

Note!

DIY ring? It's not difficult at all! A detailed master class with photos and instructions will tell you how to make a ring at home. Good luck!

website - Navigator in the world of gifts and souvenirs

Ira Fried - jeweler, designer, artist. She makes amazing pieces that are minimalistic and very vibrant. Metal meets wood, gold meets silver, to wrap around your finger in a graceful ring. Pendants are fragile twigs, earrings are fragments, drops. Periods, commas and quotation marks - stylish and “tasty”, just the way I like them :)

In her work she is guided by two rules:
Simplicity will save the world!
There are no ideal forms in nature and I like it!

Ira is inspired by Scandinavia and minimalism, which determines the simple, northern beauty of her jewelry.

Ira has equipped a real workshop at home, because working with metal requires working on machines, being able to handle burners and even a dental drill(!)

But it’s always better to see once: Ira showed us the entire process of creating a product, in this case, a ring, from start to finish.

"So, let's begin!
First, we collect the required amount of silver and melt it in crucibles into a total mass.

When the metal becomes liquid, we pour it into the mold. The metal is fixed in it and cools instantly...

Just like this “bullet”. Bullets can be different depending on what “caliber” we have chosen.

Next, in order to get closer to the shape of the ring, we need to make a strip from the “bullet”. To do this, we need a Roller machine, where metal is rolled between two shafts. First, we level the square to the required size in the grooved shafts, and then we roll it in the flat shafts and get a strip of the required thickness.

When rolling metal, it needs to be periodically annealed, or as jewelers say, “released.” This is done in order to relieve stress from the metal so that it can be rolled further more easily.

To get a specific ring, for example size 17.5, we need to measure out a strip of the desired size. They suggested an excellent formula that I always use: strip thickness 1.7 times 3 + ring size 17.5 times 3 = 57.6 mm (required strip length). Then we need to connect the edges and close them into a circle.

They must close very tightly, only then can we quickly and well seal the ring. We do this using a torch and solder (an alloy of silver and other metals).

When the ends are firmly fastened, we put this strange shape on the Rigle and, to spite the neighbors, knock on the future ring with a wooden hammer, giving it the ideal shape and the desired size. And now we already have a full-fledged ring that can be put on your finger, although it’s not very beautiful yet :) Let’s start decorating it. First, we throw it into the bleach for 2-3 minutes and the blackness disappears from the ring.

Then we carefully work with a file, smooth out all the irregularities and release the beauty of the metal.

Don’t forget to collect silver filings, they will later turn into equally beautiful rings :)

After the file, we go to the drill and sand the ring a little more with sandpaper. And now, the ring is ready! But we don’t have a simple ring, but with a duck.

We scratch an approximate drawing on the ring and move on to all well-known dental burs. No, no, we won’t treat the teeth yet, but they will help us make a duck.

Somehow, working with burs, we first get something similar to a duck, and then a real one. Quack quack!:)

In order for the duck to be clearly visible on our ring, it needs to be blackened. There are different methods of blackening, one of them is very simple and I use it for small parts. Blackening is done using a candle and iodine. So, first you need to smoke the required area, and then cauterize it with iodine.

Every day, future spouses, couples in love and people preparing to celebrate their wedding anniversary come to the Zelenin&Yolkin jewelry workshop. The idea of ​​how to do it came to Russia not so long ago from Europe.

The desire to surprise a loved one, please him and give him something truly worthwhile drives each of us, and creating a ring with your own hands means giving a large part of yourself in a small piece of jewelry.

Of course, after all, a master class on creating wedding rings is a symbolic and touching event, both for a couple in love and for spouses, and the opportunity to create your own individual ring design attracts lovers of exclusive jewelry.

How to make wedding rings with your own hands - master class

Let's start with the positive aspects of the master class on creating rings:

New opportunities

Many people think that they cannot create, for example, a gold ring with a diamond, because jewelry requires perseverance, a keen eye and titanic patience. However, the jewelry workshop “Zelenin&Yolkin” daily witnesses how even the most timid apprentices create real masterpieces with their own hands. Master jewelry making skills in three to four hours? Easily!

This is so lovely!

In fact, this is how guests rate rings they have just made with their own hands. It is impossible not to appreciate such rings, and the story of the creation of the ring remains in the memory for a lifetime.

New life for old jewelry

Often young people come to us with their jewelry, which has lost its pristine beauty under the yoke of “millennia”. Heirloom jewelry inherited from grandmothers and their grandmothers sometimes needs a new life. This is exactly what their current owners think. Therefore, many come to make wedding rings from their gold. Giving life to an old piece of jewelry that will shine with new colors - isn’t this a miracle?

A test of strength or an opportunity to prove yourself

This is exactly what lovers think when they take on what at first seems like a difficult job. Step by step, coping with each stage of creating a ring, guests experience indescribable emotions: “I didn’t know that I could do this!”

Exclusive rings

The female half will probably like this more. Lovers of beautiful things that will belong to them alone - in stores you will have to pay a fortune for such decoration, but here you can create your sketch the most unique ring, which will definitely be made in one single copy.

Ideal gift

Often people come to the jewelry workshop who want to make a ring as a gift: to their mother, a loved one, their best friend, their child, etc. The ring is especially valuable because it is created by hand, and the best gift is one made by yourself. A commemorative inscription, date, etc. is usually placed on the back of the ring.

Save time

It would seem that 3-4 hours, during which a master class on creating wedding rings takes place, is not so little. However, Moscow residents know that searching for rings that both spouses will like will take much more time, and disputes over the texture and design of rings without a professional jeweler may lead to nothing at all.

Disadvantages of making wedding rings with your own hands

The downside to taking a DIY ring making class is that you will actually have to put in some effort to make the jewelry you want. Sometimes people simply don’t like to “bother”, and it’s easier for them to buy than to make it themselves. In this case, in our workshop, jewelers will make absolutely any wedding rings to order.

How is the master class going?

The master class on making wedding rings with your own hands in Moscow takes place in several stages:

• Once the ring model and basic parameters have been selected, guests can begin creating rings.

• The jeweler shows how to work with precious metal and gives guests the opportunity to create a ring themselves according to the best traditions of jewelry making.

• The prepared precious metal is melted with a burner in a crucible and mixed with the alloy to obtain the required sample and color. The alloy is poured into a cast iron mold, which gives it the shape of an ingot.

• The finished ingot is rolled through a rolling press. This allows the rectangular block to turn into a blank for the required product.

• A long plate is bent into the shape of a ring, and its ends are soldered.

• The end result is an almost finished ring, which just needs to be perfected.

• The product is placed on the crossbar, and with the help of a textolite hammer it is given the ideal ring shape.

• At the next stage, you can start setting the precious stones, engraving and creating the necessary texture. After all, all that remains is to polish the treasured ring and try it on. Even seemingly simple wedding rings play with different colors and radiate the creator’s energy, warmth and atmosphere.

Useful tips

The most wonderful spring holiday is just around the corner, and I want to prepare for my beloved women something special. Why not make a gift for March 8th with your own hands? We offer you ideas for creating original jewelry that will delight your loved ones.

DIY bracelets

Elegant bracelet– a wonderful decoration that is loved by women all over the world. It turns out that making an original bracelet with your own hands is not so difficult. Materials for these fun little things can be purchased at specialized stores, including online stores that offer accessories for DIY jewelry.

What you may need for a double bracelet:

-- Leather lace 1.5 millimeters thick and 1-1.5 meters long

Yellow copper ball chain or rhinestone braid 30-40 centimeters long (about enough to wrap around your wrist twice)

Waxed lace or any thick thread 1.5-1.8 meters long

Yellow copper hex nut 0.6 centimeters in diameter

-- Scissors

The braid with rhinestones looks something like this. It can be found in any jewelry supply store.

Let's get started:

1) Fold the leather cord in half to make a loop. This loop will serve as a clasp and into it the nut should fit. Tie a loop with colored waxed thread and wrap it around the base 5-6 times so that the thread does not subsequently loosen or come undone.

2) Place a ball chain in the center of the leather cord and begin tying it with colored thread, grabbing each bead one at a time.

3) Continue tying the leather cord with the ball chain until you have product of the desired length to wrap your wrist twice.

4) When the desired length is reached and the ball chain ends, tie the leather lace with colored thread several times and tie the end of the leather cord with a knot.

5) Place a nut on top and make another knot to secure it.

6) Cut off the unnecessary lace at the end with scissors, wrap it around your wrist and secure the “lock”. The bracelet is ready!

The length and quantity of materials are indicated for a double bracelet, but you can make single or triple bracelets. The threads can be any color of your choice.

DIY pin bracelet

Bracelets made of pins and beads- a beautiful and very simple decoration that can be made in several versions, it all depends on your imagination and available materials.

What you will need:

-- Pins

Beads

-- Elastic stretch cord

Let's get started:

1) Do many blanks from beads and pins. Combine colors as your imagination wishes: you can make single-color rows, or multi-colored ones. Beads of different sizes and textures also look good side by side.

2) Prepare 2 long pieces of elastic cord and string pins on them.

3) Pin the ends of the laces together when the bracelet reaches the desired length. As you work, place the bracelet on your wrist to check its length. Don't make it too tight that it restricts the blood flow, or too loose that it flops around.

DIY leather bracelet

Leather rope bracelet in the form of a pigtail, wrapped several times around the hand, it looks quite cute, despite the rather rough material. Making it yourself is very simple.

What you will need:

-- Leather or suede lace (1)

Scissors (2)

Pliers (3)

Clasp (4)

Two rings (5)

Two jewelry clips (6)

-- Wrench (7)

Let's get started:

1) Cut a piece of leather cord long enough to be wrapped around your wrist 4 times without being too tight.

2) Cut 2 more pieces of cord of the same length.

3) Hold the ends of all three laces and secure them with a clip.

4) Using a wrench, secure the laces to the edge of the table to make the product easier to work with. Next, braid the cords.

5) Cut off the excess edge and place a second clamp on the other end of the cords, pressing it firmly.

6) Attach a clasp to the ends of the bracelet using rings. The decoration is ready.

Very interesting bracelets are made when macrame technique is combined with beads. These bracelets are called Shambhala bracelets. Learning how to make these bracelets is not difficult. The main thing is to understand the principle.

DIY Shambhala bracelet (video)

How to make a ring with your own hands

Do you think that it is impossible to make an original ring at home? You are wrong! It turns out that in your home you can find a lot of unnecessary things, which may be useful to you in your work. Let's take, for example, old forks, spoons, knives that you haven't used for a long time, but you feel sorry to throw them away.

We offer an idea on how in a couple of minutes you can make from old iron utensils with elegant handles original ring.

What you will need:

-- Any old forks, knives, spoons with beautifully decorated handles. This is the basis of your product. It's better if it's silver

-- Metal cutter or hacksaw

Pliers

Sandpaper

Sheet of loose paper

-- Pen

Let's get started:

1) First, decide for yourself, what kind of rings do you want to get?. You can choose the one that seems to wrap around your finger - type 1 (Fig. 1), or one of its ends will be hidden and will not be visible - type 2 (Fig. 2). The length of the workpiece depends on this.

2) At the second stage, you need to choose a suitable cutlery, which will soon turn into a ring.

3) Take a strip of paper and wrap it around your finger, on which you will wear the ring. Mark with a pen where the strip meets the other end. If you choose ring type 2, add approximately 6 millimeters and put a bold mark. If you chose a type 1 ring, then there is no need to add extra millimeters.

4) Using the resulting paper measurement, you can make a blank for the ring by cutting off the fork handle in the right place using metal cutter or hacksaw.

5) Sand the cut edge of the fork so it's not sharp and you won't get hurt when the ring is finished.

6) In the last step you need to carefully use pliers bend the resulting tip of the fork into a ring. If the fork is made of silver, you can bend it without problems.

7) The result should be something like this:

DIY ring with stone

Another very stylish and original ring can be made from a simple pebble that you find on the street, wire and paint. In the example we will show how to easily and quickly make a ring with a “piece of gold”.

What you will need:

-- Pebble of your favorite shape

Golden wire 15-20 centimeters long

Blank for dimensionless ring

Superglue for jewelry

-- Spray can with gold paint

Let's get started:

1) First you need to paint the stone from spray paint. To do this, place a pebble on a sheet of paper and direct a stream of paint at it. Once dry, turn the stone over and work on the other side.

2) Using superglue, glue the ring to the stone. The ring should be made of solid wire or metal and it is better if it is heavy enough. It is also important that you can adjust ring size.

3) Wrap the wire around the stone together with the ring several times. This will help attach the stone more tightly to the ring, and will also be part of the original design.

4) Wrap the remaining wire around the ring.

5) As a result, you will get a very stylish decoration. You can use any paint you like.

Homemade button ring

In the jewelry making materials store you can purchase ring base, to which you can attach any details: buttons, beads and other materials. An original ring can be made from old bright buttons and a piece of fabric.

What you will need:

-- A round piece of thin black felt about 5 centimeters in diameter (1)

Decorative buttons in desired colors (2)

Superglue, but an electric glue gun is better (3)

Ring with base (4)

-- Jewelry pliers (5)

Let's get started:

1) Remove the sewing loops from the buttons using pliers.

2) Glue the buttons to a piece of felt from the center in a circle close to each other to make a round shape. Let the glue dry thoroughly.

3) Cut off the excess felt from the sides. The edges can be left a little uneven.

4) Lubricate the base of the ring well with glue.

5) Glue the ring to the button part you received earlier. Let dry.

DIY necklaces

Necklace– a wonderful decoration that always catches the eye. If you love large, bright necklaces, we suggest you try making one using embellished pistachio shells.

What you will need:

-- Single pistachio shells (1)

A small piece of thick cardboard (2)

Glue gun or superglue (3)

Nail polish or acrylic paint (4)

Brush (5)

Chain (6)

2 rings and clasp (7)

Needle nose pliers (8)

-- Scissors (9)

Let's get started:

1) Cut out a semicircular pattern from cardboard that will become the base of your necklace. Its size is up to you.

2) Attach rings and a chain to the edges of the pattern using needle-nose pliers.

3) Prepare shells for pistachios, having previously painted them in the desired colors.

4) Using glue, glue the shells to the base, starting from the edge. Advice: Before gluing, attach the shells to the cardboard and think about how you will lay them out.

DIY beaded necklace

To make this decoration you need to select beads of desired color. The size of the necklace largely depends on the size of the individual beads, so if you want a thicker piece, choose larger beads. It's hard to say how many beads you might need, but it's better to have extra.

What you will need:

-- Beads of the same or different colors (1)

Chain (2)

Scissors (3)

Needle nose pliers (4)

Adjustable rings – 2 pieces (5)

Clasp (6)

Calottes - special clips for attaching beads to a chain and masking knots (7)

-- Fishing line or thick thread (8)

Let's get started:

1) Cut 6 pieces thread or fishing line approximately 25 centimeters, on each of which string beads approximately 15 centimeters.

2) You should succeed 6 strands of beads, from which you need to make 3 pairs, connecting the ends of two threads and securing them at the edges with calottes. Make sure the knot is tied as close to the beads as possible so they don't dangle. Cut off the excess thread.

3) Connect 3 pairs of threads to the chain using a ring, and then do the same with the other ends.

Advice: Before connecting the other ends of the beads to the chain, braid them to create a weave effect.

4) The chain must first be divided into 2 parts depending on the desired length and connect both ends with the clasp.

5) As a result, you should end up with a necklace like this:

DIY neck decoration

An original neck decoration can be made from a simple champagne corks with a little imagination.

What you will need:

-- Cutting board

Sharp knife

Champagne cork

Super glue

Leather or suede cord about 1 meter long

A beautiful button or earring with a stone for the centerpiece

Nuts: 1 regular hex and 2 cap nuts

-- Pin

Let's get started:

1) Using a knife, cut about one-third of the length of the cork. Make two holes in the larger half using a drill, and then use a pin to thread the two ends of the lace through both holes.

2) Thread the ends of the laces through the nut and secure it to the bottom of the plug. To the ends of the laces glue the cap nuts. Attach an earring or button to the center of the cork on the convex side.

As a result, you will get an original decoration, the length of which can be adjusted.

DIY hairpins

Hair clip can be made using a piece of lace beads and feathers. This original vintage style hairpin is suitable not only for bridesmaid dresses, but also for other festive outfits.

What you will need:

-- Lace ribbon 2-2.5 centimeters thick and 45 centimeters long

A piece of white felt

Scissors

Glue gun

Threads with a needle

Bead or decorative button

-- Base for hairpins

Let's get started:

1) Sew a white lace ribbon with thread so that, after tightening the thread, you can roll up a flower. You can sew by hand or use a sewing machine.

2) Cut a circle from felt with a diameter of approximately 5 centimeters. Glue the lace to the felt using a glue gun.

3) Glue a couple of feathers and a hairpin to the felt on the back side. Let the glue dry.

4) Glue or sew a bead or decorative button in the central part.

DIY feather hair clip

Hair clips with feathers look very impressive. If these are bright and colorful feathers, then the decoration is suitable for festive outfits; if the feathers are of natural colors, such hairpins can be worn with everyday outfits.

What you will need:

-- Regular base for hairpins

A piece of felt material

A glass or any round measure to cut out an even circle

Beads or decorative buttons

Scissors

--Glue gun or superglue

Let's get started:

1) Using a glass or other device, cut out two circles with the diameter about 5 centimeters or more depending on the size of the base clip.

2) After making the slits, insert the base into one circle of felt.

3) Glue two circles of fabric together with glue to strengthen the base clip.

4) Glue the first bottom layer of feathers on the back side, then the top one.

5) Glue a bead or decorative button to the center.

6) The hairpin is ready.

DIY earrings

Interesting update option hoop earrings You can make your own by adding hanging laces to them. If you're tired of your regular hoop earrings, updating them couldn't be easier. Moreover, laces They are as easy to remove as they are to attach, so you can restore your earrings to their original look at any time.

What you will need:

-- Any hoop earrings, in the example - with a detail inside the ring

Thin laces of any color

-- Scissors

Let's get started:

1) Prepare the desired number of laces of the required length depending on the size of the ring. Please note that the lace will be folded in half.

2) Fold the lace in half and pass the ends through the loop, grabbing the ring as shown in the photo. Do the same with all the laces.

3) In the end you will have a product like this with “fringe”. You can also trim the ends of the laces with scissors.

DIY feather earrings

Jewelry that is used as details looks very original. bird feathers. Feathers can be purchased at a jewelry supply store, or found elsewhere. In stores there are feathers not only of natural colors, but also artificially colored ones.

5) Attach a hook to the ring.

6) As a result, you get an earring like this. Make the second earring in the same way.

Everyone brainiacs greetings! Today I'll tell you like with your own hands turn an ordinary nut into a ring, well, maybe not quite a ring, but definitely into a signet ring.

Step 1: Materials

Nut (to fit your finger, my nut is 2cm)
Angle grinder (grinder)
dremel
file
sandpaper (220, 600)
masking tape
sharp knife
power unit
common salt solution
cotton buds
varnish

Step 2: Stitching the corners

Carefully, observing safety regulations when working with power tools, grind off the corners of the nut. You can tighten the nut in brain tests and use a grinder to round the corners one by one. Be sure to check that the material is removed evenly, and do not forget that one plane of the nut remains intact.

Step 3: Taper

When the corners are removed, we proceed to narrowing, that is, giving the nut the shape of a ring. We cut/stitch the material from the sides, narrowing it towards the bottom. We constantly check for symmetry, do not grind down too much, so as not to spoil it.

After narrowing it down under the tree Enough, we remove small chamfers along the edges of the signet and modify the shape at your discretion.

Step 4: Hole

At this stage, we pick up a suitable tool for removing the internal thread and forming a hole for the finger. I took my trusty “friend” - a Dremel, and grinded the threads for 15 minutes, so that the nut became hot.

We grind the material evenly, maintain symmetry, be sure to make internal chamfers and check how homemade sits on your finger.

Step 5: Sanding

We replace the Dremel with a file and clean and polish our brain trick, smooth out the grooves from the grinder and Dremel. After this, we complete the sanding with sandpaper of various grits, starting from 220 and up to 600.

I don't like rings that are too shiny, so I went with the level of polish shown in the photo, but you can bring the ring as smooth as you like.

Step 6: Print Design

Turn on brain fantasy and develop a design that we will apply to the ring. For example, I stylized my initials, reflected them symmetrically and drew them better so that the print was clear.

Step 7: Preparing for Etching

We will carry out the etching process by electrolysis, so we cover the surface of the ring that should be untouched with nail polish, adhesive tape or something similar. To do this, I chose masking tape, which I tightly glued to the ring, and then evenly and carefully cut out the previously invented design on it with a sharp knife.

Step 8: Etching

The etching process is quite interesting. I did it several times and I will say that everything is not as difficult and dangerous as it seems, although the smell is not very pleasant, but you can just close your mouth. And as a source brain flow I use a 12V charger.

So, we dilute the salt solution and connect the positive charger wire to the ring. We dip a cotton swab in a saline solution and attach a negative wire to it in a wet place, then use the resulting “electrode” stick to pass through those places crafts that need to be etched. At the same time, the longer you hold the stick, the more this place will be etched. Since this homemade not just a ring, but a signet, then I etched quite deep grooves so that the imprint would be clear. And the whole process took about 5 minutes and 7 sticks.

After etching is complete, disconnect the wires, wipe the signet in water and remove the tape. Perhaps in those places where the adhesive tape did not stick well, unnecessary etching resulted, but I think this is not critical.

Step 9: Varnishing

After the first day of wearing the ring, my finger became “rusty”, that is, the homemade product has oxidized, so I recommend that you cover the signet with colorless varnish. That's what I did - covered brainprinter polyurethane varnish.

Step 10: Craft ready!

The signet ring made from a regular nut is ready, thank you for your attention.

Good luck in brain creativity!